605 lines
12 KiB
Plaintext
605 lines
12 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Copyright (c) 2024 Rockchip Electronics Co., Ltd.
|
|
*
|
|
*/
|
|
|
|
#include <dt-bindings/usb/pd.h>
|
|
#include "rk3576-evb.dtsi"
|
|
#include "rk3576-rk806.dtsi"
|
|
|
|
/ {
|
|
es8388_sound: es8388-sound {
|
|
status = "okay";
|
|
compatible = "rockchip,multicodecs-card";
|
|
rockchip,card-name = "rockchip-es8388";
|
|
hp-det-gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
|
|
io-channels = <&saradc 3>;
|
|
io-channel-names = "adc-detect";
|
|
keyup-threshold-microvolt = <1800000>;
|
|
poll-interval = <100>;
|
|
spk-con-gpio = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
|
|
hp-con-gpio = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
|
|
rockchip,pre-power-on-delay-ms = <30>;
|
|
rockchip,post-power-down-delay-ms = <40>;
|
|
rockchip,format = "i2s";
|
|
rockchip,mclk-fs = <256>;
|
|
rockchip,cpu = <&sai1>;
|
|
rockchip,codec = <&es8388>;
|
|
rockchip,audio-routing =
|
|
"Headphone", "LOUT1",
|
|
"Headphone", "ROUT1",
|
|
"Speaker", "LOUT2",
|
|
"Speaker", "ROUT2",
|
|
"Headphone", "Headphone Power",
|
|
"Headphone", "Headphone Power",
|
|
"Speaker", "Speaker Power",
|
|
"Speaker", "Speaker Power",
|
|
"LINPUT1", "Main Mic",
|
|
"LINPUT2", "Main Mic",
|
|
"RINPUT1", "Headset Mic",
|
|
"RINPUT2", "Headset Mic";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hp_det>;
|
|
play-pause-key {
|
|
label = "playpause";
|
|
linux,code = <KEY_PLAYPAUSE>;
|
|
press-threshold-microvolt = <2000>;
|
|
};
|
|
};
|
|
|
|
pdmics: dummy-codec {
|
|
status = "disabled";
|
|
compatible = "rockchip,dummy-codec";
|
|
#sound-dai-cells = <0>;
|
|
};
|
|
|
|
pdm_mic_array: pdm-mic-array {
|
|
status = "disabled";
|
|
compatible = "simple-audio-card";
|
|
simple-audio-card,name = "rockchip,pdm-mic-array";
|
|
simple-audio-card,cpu {
|
|
sound-dai = <&pdm1>;
|
|
};
|
|
simple-audio-card,codec {
|
|
sound-dai = <&pdmics>;
|
|
};
|
|
};
|
|
|
|
sdio_pwrseq: sdio-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wifi_poweren_gpio>;
|
|
|
|
/*
|
|
* On the module itself this is one of these (depending
|
|
* on the actual card populated):
|
|
* - SDIO_RESET_L_WL_REG_ON
|
|
* - PDN (power down when low)
|
|
*/
|
|
post-power-on-delay-ms = <200>;
|
|
reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
|
|
status = "disabled";
|
|
};
|
|
|
|
vcc_1v8_s0: vcc-1v8-s0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc_1v8_s0";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
vin-supply = <&vcc_1v8_s3>;
|
|
};
|
|
|
|
vcc_3v3_s0: vcc-3v3-s0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc_3v3_s0";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&vcc_3v3_s3>;
|
|
};
|
|
|
|
vcc_ufs_s0: vcc-ufs-s0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc_ufs_s0";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&vcc_sys>;
|
|
};
|
|
|
|
vcc1v8_ufs_vccq2_s0: vcc1v8-ufs-vccq2-s0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc1v8_ufs_vccq2_s0";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
vin-supply = <&vcc_1v8_s3>;
|
|
};
|
|
|
|
vcc1v2_ufs_vccq_s0: vcc1v2-ufs-vccq-s0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc1v2_ufs_vccq_s0";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
vin-supply = <&vcc_sys>;
|
|
};
|
|
|
|
vcc3v3_lcd_n: vcc3v3-lcd0-n {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc3v3_lcd0_n";
|
|
regulator-boot-on;
|
|
enable-active-high;
|
|
gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
|
|
vin-supply = <&vcc_3v3_s0>;
|
|
};
|
|
|
|
vcc5v0_host: vcc5v0-host {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc5v0_host";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
|
|
vin-supply = <&vcc5v0_device>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usb_host_pwren>;
|
|
};
|
|
|
|
vbus5v0_typec: vbus5v0-typec {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vbus5v0_typec";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_HIGH>;
|
|
vin-supply = <&vcc5v0_device>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usb_otg0_pwren>;
|
|
};
|
|
|
|
vcc_mipicsi0: vcc-mipicsi0-regulator {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mipicsi0_pwr>;
|
|
regulator-name = "vcc_mipicsi0";
|
|
enable-active-high;
|
|
};
|
|
|
|
vcc_mipicsi1: vcc-mipicsi1-regulator {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mipicsi1_pwr>;
|
|
regulator-name = "vcc_mipicsi1";
|
|
enable-active-high;
|
|
};
|
|
|
|
vcc_mipidcphy0: vcc-mipidcphy0-regulator {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mipidcphy0_pwr>;
|
|
regulator-name = "vcc_mipidcphy0";
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
&combphy0_ps {
|
|
status = "okay";
|
|
};
|
|
|
|
&combphy1_psu {
|
|
status = "okay";
|
|
};
|
|
|
|
&dp {
|
|
status = "okay";
|
|
svid = <0xff01>;
|
|
};
|
|
|
|
&dp0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dp0_in_vp2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dp0_sound {
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
* mipidcphy0 needs to be enabled
|
|
* when dsi is enabled
|
|
*/
|
|
&dsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&dsi_panel {
|
|
power-supply = <&vcc3v3_lcd_n>;
|
|
};
|
|
|
|
&gmac0 {
|
|
/* Use rgmii-rxid mode to disable rx delay inside Soc */
|
|
phy-mode = "rgmii-rxid";
|
|
clock_in_out = "output";
|
|
|
|
snps,reset-gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
|
|
snps,reset-active-low;
|
|
/* Reset time is 20ms, 100ms for rtl8211f */
|
|
snps,reset-delays-us = <0 20000 100000>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð0m0_miim
|
|
ð0m0_tx_bus2
|
|
ð0m0_rx_bus2
|
|
ð0m0_rgmii_clk
|
|
ð0m0_rgmii_bus
|
|
ðm0_clk0_25m_out>;
|
|
|
|
tx_delay = <0x21>;
|
|
/* rx_delay = <0x3f>; */
|
|
|
|
phy-handle = <&rgmii_phy0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&gmac1 {
|
|
/* Use rgmii-rxid mode to disable rx delay inside Soc */
|
|
phy-mode = "rgmii-rxid";
|
|
clock_in_out = "output";
|
|
|
|
snps,reset-gpio = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
|
|
snps,reset-active-low;
|
|
/* Reset time is 20ms, 100ms for rtl8211f */
|
|
snps,reset-delays-us = <0 20000 100000>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð1m0_miim
|
|
ð1m0_tx_bus2
|
|
ð1m0_rx_bus2
|
|
ð1m0_rgmii_clk
|
|
ð1m0_rgmii_bus
|
|
ðm0_clk1_25m_out>;
|
|
|
|
tx_delay = <0x20>;
|
|
/* rx_delay = <0x3f>; */
|
|
|
|
phy-handle = <&rgmii_phy1>;
|
|
status = "okay";
|
|
};
|
|
|
|
>1x {
|
|
status = "okay";
|
|
power-supply = <&vcc3v3_lcd_n>;
|
|
};
|
|
|
|
&hdmi {
|
|
status = "okay";
|
|
enable-gpios = <&gpio2 RK_PB0 GPIO_ACTIVE_HIGH>;
|
|
rockchip,sda-falling-delay-ns = <360>;
|
|
};
|
|
|
|
&hdmi_in_vp0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&hdptxphy_hdmi {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c2 {
|
|
status = "okay";
|
|
|
|
usbc0: husb311@4e {
|
|
compatible = "hynetek,husb311";
|
|
reg = <0x4e>;
|
|
interrupt-parent = <&gpio0>;
|
|
interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usbc0_int>;
|
|
vbus-supply = <&vbus5v0_typec>;
|
|
status = "okay";
|
|
|
|
port {
|
|
usbc0_role_sw: endpoint {
|
|
remote-endpoint = <&usb_drd0_role_switch>;
|
|
};
|
|
};
|
|
|
|
usb_con: connector {
|
|
compatible = "usb-c-connector";
|
|
label = "USB-C";
|
|
data-role = "dual";
|
|
power-role = "dual";
|
|
try-power-role = "sink";
|
|
op-sink-microwatt = <1000000>;
|
|
sink-pdos =
|
|
<PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
|
|
source-pdos =
|
|
<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
|
|
mode-switch = <&dp>;
|
|
|
|
altmodes {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
altmode@0 {
|
|
reg = <0>;
|
|
svid = <0xff01>;
|
|
vdo = <0xffffffff>;
|
|
};
|
|
};
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
usbc0_orien_sw: endpoint {
|
|
remote-endpoint = <&usbdp_phy_orientation_switch>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
dp_altmode_mux: endpoint {
|
|
remote-endpoint = <&usbdp_phy_dp_altmode_mux>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c3 {
|
|
status = "okay";
|
|
es8388: es8388@10 {
|
|
status = "okay";
|
|
#sound-dai-cells = <0>;
|
|
compatible = "everest,es8388", "everest,es8323";
|
|
reg = <0x10>;
|
|
clocks = <&mclkout_sai1>;
|
|
clock-names = "mclk";
|
|
assigned-clocks = <&mclkout_sai1>;
|
|
assigned-clock-rates = <12288000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sai1m0_mclk>;
|
|
};
|
|
};
|
|
|
|
&i2c7 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c7m1_xfer>;
|
|
|
|
|
|
icm42607_acc: icm_acc@68 {
|
|
status = "okay";
|
|
compatible = "icm42607_acc";
|
|
reg = <0x68>;
|
|
irq-gpio = <&gpio1 RK_PD5 IRQ_TYPE_EDGE_RISING>;
|
|
irq_enable = <0>;
|
|
poll_delay_ms = <30>;
|
|
type = <SENSOR_TYPE_ACCEL>;
|
|
layout = <4>;
|
|
};
|
|
|
|
icm42607_gyro: icm_gyro@68 {
|
|
status = "okay";
|
|
compatible = "icm42607_gyro";
|
|
reg = <0x68>;
|
|
poll_delay_ms = <30>;
|
|
type = <SENSOR_TYPE_GYROSCOPE>;
|
|
layout = <4>;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
rgmii_phy0: phy@1 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <0x1>;
|
|
clocks = <&cru REFCLKO25M_GMAC0_OUT>;
|
|
};
|
|
};
|
|
|
|
&mdio1 {
|
|
rgmii_phy1: phy@1 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <0x1>;
|
|
clocks = <&cru REFCLKO25M_GMAC1_OUT>;
|
|
};
|
|
};
|
|
|
|
&mipidcphy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
reset-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
|
|
rockchip,skip-scan-in-resume;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wifi_poweren_gpio>;
|
|
status = "okay";
|
|
};
|
|
|
|
&pdm1 {
|
|
status = "disabled";
|
|
pinctrl-names = "default", "idle", "clk";
|
|
pinctrl-0 = <&pdm1m1_sdi0
|
|
&pdm1m1_sdi1
|
|
&pdm1m1_sdi2
|
|
&pdm1m1_sdi3>;
|
|
pinctrl-1 = <&pdm1m1_clk0_idle
|
|
&pdm1m1_clk1_idle>;
|
|
pinctrl-2 = <&pdm1m1_clk0
|
|
&pdm1m1_clk1>;
|
|
};
|
|
|
|
&pinctrl {
|
|
cam {
|
|
mipicsi0_pwr: mipicsi0-pwr {
|
|
rockchip,pins =
|
|
/* camera power en */
|
|
<3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
|
|
mipicsi1_pwr: mipicsi1-pwr {
|
|
rockchip,pins =
|
|
/* camera power en */
|
|
<3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
|
|
mipidcphy0_pwr: mipidcphy0-pwr {
|
|
rockchip,pins =
|
|
/* camera power en */
|
|
<3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
headphone {
|
|
hp_det: hp-det {
|
|
rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
|
|
};
|
|
};
|
|
|
|
usb {
|
|
usb_host_pwren: usb-host-pwren {
|
|
rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
|
|
usb_otg0_pwren: usb-otg0-pwren {
|
|
rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
|
|
usbc0_int: usbc0-int {
|
|
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
|
|
};
|
|
};
|
|
|
|
wireless-bluetooth {
|
|
uart4_gpios: uart4-gpios {
|
|
rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
wireless-wlan {
|
|
wifi_host_wake_irq: wifi-host-wake-irq {
|
|
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
|
|
};
|
|
|
|
wifi_poweren_gpio: wifi-poweren-gpio {
|
|
rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&route_hdmi {
|
|
status = "okay";
|
|
connect = <&vp0_out_hdmi>;
|
|
};
|
|
|
|
&sai1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sai1m0_lrck
|
|
&sai1m0_sclk
|
|
&sai1m0_sdi0
|
|
&sai1m0_sdo0>;
|
|
};
|
|
|
|
&sdio {
|
|
max-frequency = <200000000>;
|
|
no-sd;
|
|
no-mmc;
|
|
bus-width = <4>;
|
|
disable-wp;
|
|
cap-sd-highspeed;
|
|
cap-sdio-irq;
|
|
keep-power-in-suspend;
|
|
mmc-pwrseq = <&sdio_pwrseq>;
|
|
non-removable;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdmmc1m0_bus4 &sdmmc1m0_clk &sdmmc1m0_cmd>;
|
|
sd-uhs-sdr104;
|
|
status = "disabled";
|
|
};
|
|
|
|
&sdmmc {
|
|
status = "okay";
|
|
};
|
|
|
|
&spdif_tx3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ufs {
|
|
vcc-supply = <&vcc_ufs_s0>;
|
|
vccq-supply = <&vcc1v2_ufs_vccq_s0>;
|
|
vccq2-supply = <&vcc1v8_ufs_vccq2_s0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&u2phy0_otg {
|
|
rockchip,typec-vbus-det;
|
|
};
|
|
|
|
&u2phy1_otg {
|
|
phy-supply = <&vcc5v0_host>;
|
|
};
|
|
|
|
&usbdp_phy {
|
|
orientation-switch;
|
|
svid = <0xff01>;
|
|
sbu1-dc-gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
|
|
sbu2-dc-gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_HIGH>;
|
|
|
|
port {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
usbdp_phy_orientation_switch: endpoint@0 {
|
|
reg = <0>;
|
|
remote-endpoint = <&usbc0_orien_sw>;
|
|
};
|
|
|
|
usbdp_phy_dp_altmode_mux: endpoint@1 {
|
|
reg = <1>;
|
|
remote-endpoint = <&dp_altmode_mux>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_drd0_dwc3 {
|
|
dr_mode = "otg";
|
|
usb-role-switch;
|
|
port {
|
|
usb_drd0_role_switch: endpoint {
|
|
remote-endpoint = <&usbc0_role_sw>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_drd1_dwc3 {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&vp0 {
|
|
status = "okay";
|
|
};
|