// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
 *
 */

#include <dt-bindings/usb/pd.h>
#include "rk3576-evb.dtsi"
#include "rk3576-rk806.dtsi"

/ {
	es8388_sound: es8388-sound {
		status = "okay";
		compatible = "rockchip,multicodecs-card";
		rockchip,card-name = "rockchip-es8388";
		hp-det-gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
		io-channels = <&saradc 3>;
		io-channel-names = "adc-detect";
		keyup-threshold-microvolt = <1800000>;
		poll-interval = <100>;
		spk-con-gpio = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
		hp-con-gpio = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
		rockchip,pre-power-on-delay-ms = <30>;
		rockchip,post-power-down-delay-ms = <40>;
		rockchip,format = "i2s";
		rockchip,mclk-fs = <256>;
		rockchip,cpu = <&sai1>;
		rockchip,codec = <&es8388>;
		rockchip,audio-routing =
			"Headphone", "LOUT1",
			"Headphone", "ROUT1",
			"Speaker", "LOUT2",
			"Speaker", "ROUT2",
			"Headphone", "Headphone Power",
			"Headphone", "Headphone Power",
			"Speaker", "Speaker Power",
			"Speaker", "Speaker Power",
			"LINPUT1", "Main Mic",
			"LINPUT2", "Main Mic",
			"RINPUT1", "Headset Mic",
			"RINPUT2", "Headset Mic";
		pinctrl-names = "default";
		pinctrl-0 = <&hp_det>;
		play-pause-key {
			label = "playpause";
			linux,code = <KEY_PLAYPAUSE>;
			press-threshold-microvolt = <2000>;
		};
	};

	pdmics: dummy-codec {
		status = "disabled";
		compatible = "rockchip,dummy-codec";
		#sound-dai-cells = <0>;
	};

	pdm_mic_array: pdm-mic-array {
		status = "disabled";
		compatible = "simple-audio-card";
		simple-audio-card,name = "rockchip,pdm-mic-array";
		simple-audio-card,cpu {
			sound-dai = <&pdm1>;
		};
		simple-audio-card,codec {
			sound-dai = <&pdmics>;
		};
	};

	sdio_pwrseq: sdio-pwrseq {
		compatible = "mmc-pwrseq-simple";
		pinctrl-names = "default";
		pinctrl-0 = <&wifi_poweren_gpio>;

		/*
		 * On the module itself this is one of these (depending
		 * on the actual card populated):
		 * - SDIO_RESET_L_WL_REG_ON
		 * - PDN (power down when low)
		 */
		post-power-on-delay-ms = <200>;
		reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
		status = "disabled";
	};

	vcc_1v8_s0: vcc-1v8-s0 {
		compatible = "regulator-fixed";
		regulator-name = "vcc_1v8_s0";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		vin-supply = <&vcc_1v8_s3>;
	};

	vcc_3v3_s0: vcc-3v3-s0 {
		compatible = "regulator-fixed";
		regulator-name = "vcc_3v3_s0";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&vcc_3v3_s3>;
	};

	vcc_ufs_s0: vcc-ufs-s0 {
		compatible = "regulator-fixed";
		regulator-name = "vcc_ufs_s0";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&vcc_sys>;
	};

	vcc1v8_ufs_vccq2_s0: vcc1v8-ufs-vccq2-s0 {
		compatible = "regulator-fixed";
		regulator-name = "vcc1v8_ufs_vccq2_s0";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		vin-supply = <&vcc_1v8_s3>;
	};

	vcc1v2_ufs_vccq_s0: vcc1v2-ufs-vccq-s0 {
		compatible = "regulator-fixed";
		regulator-name = "vcc1v2_ufs_vccq_s0";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1200000>;
		regulator-max-microvolt = <1200000>;
		vin-supply = <&vcc_sys>;
	};

	vcc3v3_lcd_n: vcc3v3-lcd0-n {
		compatible = "regulator-fixed";
		regulator-name = "vcc3v3_lcd0_n";
		regulator-boot-on;
		enable-active-high;
		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc_3v3_s0>;
	};

	vcc5v0_host: vcc5v0-host {
		compatible = "regulator-fixed";
		regulator-name = "vcc5v0_host";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc5v0_device>;
		pinctrl-names = "default";
		pinctrl-0 = <&usb_host_pwren>;
	};

	vbus5v0_typec: vbus5v0-typec {
		compatible = "regulator-fixed";
		regulator-name = "vbus5v0_typec";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc5v0_device>;
		pinctrl-names = "default";
		pinctrl-0 = <&usb_otg0_pwren>;
	};

	vcc_mipicsi0: vcc-mipicsi0-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipicsi0_pwr>;
		regulator-name = "vcc_mipicsi0";
		enable-active-high;
	};

	vcc_mipicsi1: vcc-mipicsi1-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipicsi1_pwr>;
		regulator-name = "vcc_mipicsi1";
		enable-active-high;
	};

	vcc_mipidcphy0: vcc-mipidcphy0-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipidcphy0_pwr>;
		regulator-name = "vcc_mipidcphy0";
		enable-active-high;
	};
};

&combphy0_ps {
	status = "okay";
};

&combphy1_psu {
	status = "okay";
};

&dp {
	status = "okay";
	svid = <0xff01>;
};

&dp0 {
	status = "okay";
};

&dp0_in_vp2 {
	status = "okay";
};

&dp0_sound {
	status = "okay";
};

/*
 * mipidcphy0 needs to be enabled
 * when dsi is enabled
 */
&dsi {
	status = "okay";
};

&dsi_panel {
	power-supply = <&vcc3v3_lcd_n>;
};

&gmac0 {
	/* Use rgmii-rxid mode to disable rx delay inside Soc */
	phy-mode = "rgmii-rxid";
	clock_in_out = "output";

	snps,reset-gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
	snps,reset-active-low;
	/* Reset time is 20ms, 100ms for rtl8211f */
	snps,reset-delays-us = <0 20000 100000>;

	pinctrl-names = "default";
	pinctrl-0 = <&eth0m0_miim
		     &eth0m0_tx_bus2
		     &eth0m0_rx_bus2
		     &eth0m0_rgmii_clk
		     &eth0m0_rgmii_bus
		     &ethm0_clk0_25m_out>;

	tx_delay = <0x21>;
	/* rx_delay = <0x3f>; */

	phy-handle = <&rgmii_phy0>;
	status = "okay";
};

&gmac1 {
	/* Use rgmii-rxid mode to disable rx delay inside Soc */
	phy-mode = "rgmii-rxid";
	clock_in_out = "output";

	snps,reset-gpio = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
	snps,reset-active-low;
	/* Reset time is 20ms, 100ms for rtl8211f */
	snps,reset-delays-us = <0 20000 100000>;

	pinctrl-names = "default";
	pinctrl-0 = <&eth1m0_miim
		     &eth1m0_tx_bus2
		     &eth1m0_rx_bus2
		     &eth1m0_rgmii_clk
		     &eth1m0_rgmii_bus
		     &ethm0_clk1_25m_out>;

	tx_delay = <0x20>;
	/* rx_delay = <0x3f>; */

	phy-handle = <&rgmii_phy1>;
	status = "okay";
};

&gt1x {
	status = "okay";
	power-supply = <&vcc3v3_lcd_n>;
};

&hdmi {
	status = "okay";
	enable-gpios = <&gpio2 RK_PB0 GPIO_ACTIVE_HIGH>;
	rockchip,sda-falling-delay-ns = <360>;
};

&hdmi_in_vp0 {
	status = "okay";
};

&hdptxphy_hdmi {
	status = "okay";
};

&i2c2 {
	status = "okay";

	usbc0: husb311@4e {
		compatible = "hynetek,husb311";
		reg = <0x4e>;
		interrupt-parent = <&gpio0>;
		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
		pinctrl-names = "default";
		pinctrl-0 = <&usbc0_int>;
		vbus-supply = <&vbus5v0_typec>;
		status = "okay";

		port {
			usbc0_role_sw: endpoint {
				remote-endpoint = <&usb_drd0_role_switch>;
			};
		};

		usb_con: connector {
			compatible = "usb-c-connector";
			label = "USB-C";
			data-role = "dual";
			power-role = "dual";
			try-power-role = "sink";
			op-sink-microwatt = <1000000>;
			sink-pdos =
				<PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
			source-pdos =
				<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
			mode-switch = <&dp>;

			altmodes {
				#address-cells = <1>;
				#size-cells = <0>;

				altmode@0 {
					reg = <0>;
					svid = <0xff01>;
					vdo = <0xffffffff>;
				};
			};

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					usbc0_orien_sw: endpoint {
						remote-endpoint = <&usbdp_phy_orientation_switch>;
					};
				};

				port@1 {
					reg = <1>;
					dp_altmode_mux: endpoint {
						remote-endpoint = <&usbdp_phy_dp_altmode_mux>;
					};
				};
			};
		};
	};
};

&i2c3 {
	status = "okay";
	es8388: es8388@10 {
		status = "okay";
		#sound-dai-cells = <0>;
		compatible = "everest,es8388", "everest,es8323";
		reg = <0x10>;
		clocks = <&mclkout_sai1>;
		clock-names = "mclk";
		assigned-clocks = <&mclkout_sai1>;
		assigned-clock-rates = <12288000>;
		pinctrl-names = "default";
		pinctrl-0 = <&sai1m0_mclk>;
	};
};

&i2c7 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&i2c7m1_xfer>;


	icm42607_acc: icm_acc@68 {
		status = "okay";
		compatible = "icm42607_acc";
		reg = <0x68>;
		irq-gpio = <&gpio1 RK_PD5 IRQ_TYPE_EDGE_RISING>;
		irq_enable = <0>;
		poll_delay_ms = <30>;
		type = <SENSOR_TYPE_ACCEL>;
		layout = <4>;
	};

	icm42607_gyro: icm_gyro@68 {
		status = "okay";
		compatible = "icm42607_gyro";
		reg = <0x68>;
		poll_delay_ms = <30>;
		type = <SENSOR_TYPE_GYROSCOPE>;
		layout = <4>;
	};
};

&mdio0 {
	rgmii_phy0: phy@1 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <0x1>;
		clocks = <&cru REFCLKO25M_GMAC0_OUT>;
	};
};

&mdio1 {
	rgmii_phy1: phy@1 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <0x1>;
		clocks = <&cru REFCLKO25M_GMAC1_OUT>;
	};
};

&mipidcphy0 {
	status = "okay";
};

&pcie0 {
	reset-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
	rockchip,skip-scan-in-resume;
	pinctrl-names = "default";
	pinctrl-0 = <&wifi_poweren_gpio>;
	status = "okay";
};

&pdm1 {
	status = "disabled";
	pinctrl-names = "default", "idle", "clk";
	pinctrl-0 = <&pdm1m1_sdi0
		     &pdm1m1_sdi1
		     &pdm1m1_sdi2
		     &pdm1m1_sdi3>;
	pinctrl-1 = <&pdm1m1_clk0_idle
		     &pdm1m1_clk1_idle>;
	pinctrl-2 = <&pdm1m1_clk0
		     &pdm1m1_clk1>;
};

&pinctrl {
	cam {
		mipicsi0_pwr: mipicsi0-pwr {
			rockchip,pins =
				/* camera power en */
				<3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
		};

		mipicsi1_pwr: mipicsi1-pwr {
			rockchip,pins =
				/* camera power en */
				<3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
		};

		mipidcphy0_pwr: mipidcphy0-pwr {
			rockchip,pins =
				/* camera power en */
				<3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	headphone {
		hp_det: hp-det {
			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
		};
	};

	usb {
		usb_host_pwren: usb-host-pwren {
			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
		};

		usb_otg0_pwren: usb-otg0-pwren {
			rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
		};

		usbc0_int: usbc0-int {
			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
		};
	};

	wireless-bluetooth {
		uart4_gpios: uart4-gpios {
			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	wireless-wlan {
		wifi_host_wake_irq: wifi-host-wake-irq {
			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
		};

		wifi_poweren_gpio: wifi-poweren-gpio {
			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
		};
	};
};

&route_hdmi {
	status = "okay";
	connect = <&vp0_out_hdmi>;
};

&sai1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&sai1m0_lrck
		     &sai1m0_sclk
		     &sai1m0_sdi0
		     &sai1m0_sdo0>;
};

&sdio {
	max-frequency = <200000000>;
	no-sd;
	no-mmc;
	bus-width = <4>;
	disable-wp;
	cap-sd-highspeed;
	cap-sdio-irq;
	keep-power-in-suspend;
	mmc-pwrseq = <&sdio_pwrseq>;
	non-removable;
	pinctrl-names = "default";
	pinctrl-0 = <&sdmmc1m0_bus4 &sdmmc1m0_clk &sdmmc1m0_cmd>;
	sd-uhs-sdr104;
	status = "disabled";
};

&sdmmc {
	status = "okay";
};

&spdif_tx3 {
	status = "okay";
};

&ufs {
	vcc-supply = <&vcc_ufs_s0>;
	vccq-supply = <&vcc1v2_ufs_vccq_s0>;
	vccq2-supply = <&vcc1v8_ufs_vccq2_s0>;
	status = "okay";
};

&u2phy0_otg {
	rockchip,typec-vbus-det;
};

&u2phy1_otg {
	phy-supply = <&vcc5v0_host>;
};

&usbdp_phy {
	orientation-switch;
	svid = <0xff01>;
	sbu1-dc-gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
	sbu2-dc-gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_HIGH>;

	port {
		#address-cells = <1>;
		#size-cells = <0>;

		usbdp_phy_orientation_switch: endpoint@0 {
			reg = <0>;
			remote-endpoint = <&usbc0_orien_sw>;
		};

		usbdp_phy_dp_altmode_mux: endpoint@1 {
			reg = <1>;
			remote-endpoint = <&dp_altmode_mux>;
		};
	};
};

&usb_drd0_dwc3 {
	dr_mode = "otg";
	usb-role-switch;
	port {
		usb_drd0_role_switch: endpoint {
			remote-endpoint = <&usbc0_role_sw>;
		};
	};
};

&usb_drd1_dwc3 {
	dr_mode = "host";
	status = "okay";
};

&vp0 {
	status = "okay";
};