471 lines
14 KiB
C
471 lines
14 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (C) 2023 Rockchip Electronics Co., Ltd.
|
|
* Author: Wangqiang Guo <kay.guo@rock-chips.com>
|
|
*/
|
|
#include <linux/interrupt.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/miscdevice.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/uaccess.h>
|
|
#include <linux/atomic.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/input.h>
|
|
#include <linux/workqueue.h>
|
|
#include <linux/freezer.h>
|
|
#include <linux/of_gpio.h>
|
|
#ifdef CONFIG_HAS_EARLYSUSPEND
|
|
#include <linux/earlysuspend.h>
|
|
#endif
|
|
#include <linux/sensor-dev.h>
|
|
#include <linux/icm4260x.h>
|
|
|
|
/**
|
|
* icm4260x_set_idle() - Set Idle bit in PWR_MGMT_0 register
|
|
* @client: struct i2c_client..
|
|
*
|
|
* Set ACCEL_LP_CLK_SEL as well when necessary with a proper wait
|
|
*
|
|
* Return: 0 when successful.
|
|
*/
|
|
static int icm4260x_set_idle(struct i2c_client *client)
|
|
{
|
|
u8 reg_pwr_mgmt_0;
|
|
u8 d;
|
|
int ret = 0;
|
|
|
|
reg_pwr_mgmt_0 = sensor_read_reg(client, ICM4260X_PWR_MGMT_0);
|
|
/* set Idle bit.
|
|
* when accel LPM is already enabled, set ACCEL_LP_CLK_SEL bit as well.
|
|
*/
|
|
d = reg_pwr_mgmt_0;
|
|
d |= BIT_IDLE;
|
|
if ((d & BIT_ACCEL_MODE_MASK) == BIT_ACCEL_MODE_LPM)
|
|
d |= BIT_ACCEL_LP_CLK_SEL;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_PWR_MGMT_0, d);
|
|
usleep_range(20, 21);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/**
|
|
* icm4260x_mreg_read() - Multiple byte read from MREG area.
|
|
* @client: struct i2c_client.
|
|
* @addr: MREG register start address including bank in upper byte.
|
|
* @len: length to read in byte.
|
|
* @data: pointer to store read data.
|
|
*
|
|
* Return: 0 when successful.
|
|
*/
|
|
static int icm4260x_mreg_read(struct i2c_client *client, int addr, int len, u8 *data)
|
|
{
|
|
int ret;
|
|
u8 reg_pwr_mgmt_0;
|
|
|
|
reg_pwr_mgmt_0 = sensor_read_reg(client, ICM4260X_PWR_MGMT_0);
|
|
|
|
ret = icm4260x_set_idle(client);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_BLK_SEL_R, (addr >> 8) & 0xff);
|
|
usleep_range(INV_ICM42607_BLK_SEL_WAIT_US,
|
|
INV_ICM42607_BLK_SEL_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_MADDR_R, addr & 0xff);
|
|
usleep_range(INV_ICM42607_MADDR_WAIT_US,
|
|
INV_ICM42607_MADDR_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
*data = ICM4260X_M_R;
|
|
ret = sensor_rx_data(client, data, len);
|
|
usleep_range(INV_ICM42607_M_RW_WAIT_US,
|
|
INV_ICM42607_M_RW_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
restore_bank:
|
|
ret |= sensor_write_reg(client, ICM4260X_BLK_SEL_R, 0);
|
|
usleep_range(INV_ICM42607_BLK_SEL_WAIT_US,
|
|
INV_ICM42607_BLK_SEL_WAIT_US + 1);
|
|
|
|
ret |= sensor_write_reg(client, ICM4260X_PWR_MGMT_0, reg_pwr_mgmt_0);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/**
|
|
* icm4260x_mreg_single_write() - Single byte write to MREG area.
|
|
* @client: struct i2c_client.
|
|
* @addr: MREG register address including bank in upper byte.
|
|
* @data: data to write.
|
|
*
|
|
* Return: 0 when successful.
|
|
*/
|
|
static int icm4260x_mreg_single_write(struct i2c_client *client, int addr, u8 data)
|
|
{
|
|
int ret;
|
|
u8 reg_pwr_mgmt_0;
|
|
|
|
reg_pwr_mgmt_0 = sensor_read_reg(client, ICM4260X_PWR_MGMT_0);
|
|
|
|
ret = icm4260x_set_idle(client);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_BLK_SEL_W, (addr >> 8) & 0xff);
|
|
usleep_range(INV_ICM42607_BLK_SEL_WAIT_US,
|
|
INV_ICM42607_BLK_SEL_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_MADDR_W, addr & 0xff);
|
|
usleep_range(INV_ICM42607_MADDR_WAIT_US,
|
|
INV_ICM42607_MADDR_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
ret = sensor_write_reg(client, ICM4260X_M_W, data);
|
|
usleep_range(INV_ICM42607_M_RW_WAIT_US,
|
|
INV_ICM42607_M_RW_WAIT_US + 1);
|
|
if (ret)
|
|
goto restore_bank;
|
|
|
|
restore_bank:
|
|
ret |= sensor_write_reg(client, ICM4260X_BLK_SEL_W, 0);
|
|
usleep_range(INV_ICM42607_BLK_SEL_WAIT_US,
|
|
INV_ICM42607_BLK_SEL_WAIT_US + 1);
|
|
|
|
ret |= sensor_write_reg(client, ICM4260X_PWR_MGMT_0, reg_pwr_mgmt_0);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* OTP reload procedure.
|
|
*/
|
|
static int icm4260x_otp_reload(struct i2c_client *client)
|
|
{
|
|
int ret;
|
|
u8 rb = 0;
|
|
|
|
/* set idle bit */
|
|
ret = icm4260x_set_idle(client);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Set OTP_COPY_MODE to 2'b01 */
|
|
ret = icm4260x_mreg_read(client, ICM4260X_OTP_CONFIG_MREG_TOP1, 1, &rb);
|
|
if (ret)
|
|
return ret;
|
|
rb &= ~OTP_COPY_MODE_MASK;
|
|
rb |= BIT_OTP_COPY_NORMAL;
|
|
ret = icm4260x_mreg_single_write(client, ICM4260X_OTP_CONFIG_MREG_TOP1, rb);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* set OTP_PWR_DOWN to 1'b0 and wait for 300us */
|
|
ret = icm4260x_mreg_read(client, ICM4260X_OTP_CTRL7_MREG_OTP, 1, &rb);
|
|
if (ret)
|
|
return ret;
|
|
rb &= ~BIT_OTP_PWR_DOWN;
|
|
ret = icm4260x_mreg_single_write(client, ICM4260X_OTP_CTRL7_MREG_OTP, rb);
|
|
if (ret)
|
|
return ret;
|
|
usleep_range(300, 400);
|
|
|
|
/* set OTP_RELOAD to 1'b1 and wait for 280us */
|
|
ret = icm4260x_mreg_read(client, ICM4260X_OTP_CTRL7_MREG_OTP, 1, &rb);
|
|
if (ret)
|
|
return ret;
|
|
rb |= BIT_OTP_RELOAD;
|
|
ret = icm4260x_mreg_single_write(client, ICM4260X_OTP_CTRL7_MREG_OTP, rb);
|
|
if (ret)
|
|
return ret;
|
|
usleep_range(280, 380);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sensor_active(struct i2c_client *client, int enable, int rate)
|
|
{
|
|
struct sensor_private_data *sensor =
|
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
int result = 0;
|
|
u8 status = 0;
|
|
|
|
sensor->ops->ctrl_data = sensor_read_reg(client, sensor->ops->ctrl_reg);
|
|
|
|
if (!enable) {
|
|
status = (0xff & ~BIT_ACCEL_MODE_MASK);
|
|
sensor->ops->ctrl_data &= status;
|
|
} else {
|
|
status = BIT_ACCEL_MODE_LNM;
|
|
sensor->ops->ctrl_data |= status;
|
|
sensor->ops->ctrl_data &= ~BIT_IDLE;
|
|
}
|
|
|
|
result = sensor_write_reg(client, sensor->ops->ctrl_reg,
|
|
sensor->ops->ctrl_data);
|
|
if (result) {
|
|
dev_err(&client->dev,
|
|
"%s: fail to set pwr_mgmt0(%d)\n", __func__, result);
|
|
return result;
|
|
}
|
|
/*set powerdown will make scale change*/
|
|
sensor_write_reg(client, ICM4260X_ACCEL_CONFIG0, 0x66);
|
|
usleep_range(250, 260);
|
|
|
|
return result;
|
|
}
|
|
|
|
/*
|
|
* write POR value
|
|
*/
|
|
|
|
static int icm4260x_set_default_register(struct i2c_client *client)
|
|
{
|
|
int status = 0;
|
|
|
|
status |= sensor_write_reg(client, ICM4260X_GYRO_CONFIG0, 0x66);
|
|
status |= sensor_write_reg(client, ICM4260X_ACCEL_CONFIG0, 0x66);
|
|
status |= sensor_write_reg(client, ICM4260X_APEX_CONFIG0, 0x08);
|
|
status |= sensor_write_reg(client, ICM4260X_APEX_CONFIG1, 0x02);
|
|
status |= sensor_write_reg(client, ICM4260X_WOM_CONFIG, 0);
|
|
status |= sensor_write_reg(client, ICM4260X_FIFO_CONFIG1, 0x01);
|
|
status |= sensor_write_reg(client, ICM4260X_FIFO_CONFIG2, 0);
|
|
status |= sensor_write_reg(client, ICM4260X_FIFO_CONFIG3, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_FIFO_CONFIG5_MREG_TOP1, 0x20);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_ST_CONFIG_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_INT_SOURCE7_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_INT_SOURCE8_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_INT_SOURCE9_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_INT_SOURCE10_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG2_MREG_TOP1, 0xA2);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG3_MREG_TOP1, 0x85);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG4_MREG_TOP1, 0x51);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG5_MREG_TOP1, 0x80);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG9_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG10_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG11_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_ACCEL_WOM_X_THR_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_ACCEL_WOM_Y_THR_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_ACCEL_WOM_Z_THR_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER0_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER1_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER2_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER3_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER4_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER5_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER6_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER7_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_GOS_USER8_MREG_TOP1, 0);
|
|
status |= icm4260x_mreg_single_write(client, ICM4260X_APEX_CONFIG12_MREG_TOP1, 0);
|
|
|
|
if (status)
|
|
return -EIO;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sensor_init(struct i2c_client *client)
|
|
{
|
|
int ret = 0;
|
|
u8 device_id = 0, value = 0;
|
|
struct sensor_private_data *sensor =
|
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
|
|
device_id = sensor_read_reg(client, ICM4260X_WHO_AM_I);
|
|
if (device_id != ICM42607_DEVICE_ID) {
|
|
dev_err(&client->dev, "%s: check id err, read_id: %d\n",
|
|
__func__, device_id);
|
|
return -1;
|
|
}
|
|
|
|
ret = icm4260x_otp_reload(client);
|
|
if (ret) {
|
|
dev_err(&client->dev,
|
|
"ICM4260X OTP reload error,ret: %d!\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
|
|
ret = icm4260x_set_default_register(client);
|
|
if (ret) {
|
|
dev_err(&client->dev,
|
|
"set ICM4260X default_register error,ret: %d!\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
/* SPI or I2C only
|
|
* FIFO count : byte mode, big endian
|
|
* sensor data : big endian
|
|
*/
|
|
value |= BIT_FIFO_COUNT_ENDIAN;
|
|
value |= BIT_SENSOR_DATA_ENDIAN;
|
|
ret = sensor_write_reg(client, ICM4260X_INTF_CONFIG0, value);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* configure clock */
|
|
value = BIT_CLK_SEL_PLL | BIT_I3C_SDR_EN | BIT_I3C_DDR_EN;
|
|
ret = sensor_write_reg(client, ICM4260X_INTF_CONFIG1, value);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* INT pin configuration */
|
|
/*
|
|
* value = (INT_POLARITY << SHIFT_INT1_POLARITY) |
|
|
* (INT_DRIVE_CIRCUIT << SHIFT_INT1_DRIVE_CIRCUIT) |
|
|
* (INT_MODE << SHIFT_INT1_MODE);
|
|
* ret = sensor_write_reg(client, ICM4260X_INT_CONFIG_REG, value);
|
|
* if (ret)
|
|
* return ret;
|
|
*/
|
|
|
|
/* disable sensors */
|
|
ret = sensor_write_reg(client, ICM4260X_PWR_MGMT_0, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* set +-2g scale select for accelerometer UI interface output*/
|
|
value = 0x66;
|
|
ret = sensor_write_reg(client, ICM4260X_ACCEL_CONFIG0, value);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* turn on accelerometer*/
|
|
ret = sensor->ops->active(client, 0, sensor->pdata->poll_delay_ms);
|
|
if (ret) {
|
|
dev_err(&client->dev,
|
|
"%s: fail to active sensor(%d)\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int gsensor_report_value(struct i2c_client *client,
|
|
struct sensor_axis *axis)
|
|
{
|
|
struct sensor_private_data *sensor =
|
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
|
|
if (sensor->status_cur == SENSOR_ON) {
|
|
/* Report acceleration sensor information */
|
|
input_report_abs(sensor->input_dev, ABS_X, axis->x);
|
|
input_report_abs(sensor->input_dev, ABS_Y, axis->y);
|
|
input_report_abs(sensor->input_dev, ABS_Z, axis->z);
|
|
input_sync(sensor->input_dev);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sensor_report_value(struct i2c_client *client)
|
|
{
|
|
struct sensor_private_data *sensor =
|
|
(struct sensor_private_data *) i2c_get_clientdata(client);
|
|
struct sensor_platform_data *pdata = sensor->pdata;
|
|
int ret = 0;
|
|
short x, y, z;
|
|
struct sensor_axis axis;
|
|
u8 buffer[6] = {0};
|
|
|
|
if (sensor->ops->read_len < 6) {
|
|
dev_err(&client->dev, "%s: length is error, len = %d\n",
|
|
__func__, sensor->ops->read_len);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Data bytes from hardware xH, xL, yH, yL, zH, zL */
|
|
*buffer = sensor->ops->read_reg;
|
|
ret = sensor_rx_data(client, buffer, sensor->ops->read_len);
|
|
if (ret < 0) {
|
|
dev_err(&client->dev,
|
|
"%s: read data failed, ret = %d\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
x = ((buffer[0] << 8) & 0xff00) + (buffer[1] & 0xFF);
|
|
y = ((buffer[2] << 8) & 0xff00) + (buffer[3] & 0xFF);
|
|
z = ((buffer[4] << 8) & 0xff00) + (buffer[5] & 0xFF);
|
|
|
|
//printk("%s,x:%d, y:%d, z:%d\n", __func__, x, y, z);
|
|
axis.x = (pdata->orientation[0]) * x + (pdata->orientation[1]) * y +
|
|
(pdata->orientation[2]) * z;
|
|
axis.y = (pdata->orientation[3]) * x + (pdata->orientation[4]) * y +
|
|
(pdata->orientation[5]) * z;
|
|
axis.z = (pdata->orientation[6]) * x + (pdata->orientation[7]) * y +
|
|
(pdata->orientation[8]) * z;
|
|
|
|
gsensor_report_value(client, &axis);
|
|
|
|
mutex_lock(&(sensor->data_mutex));
|
|
sensor->axis = axis;
|
|
mutex_unlock(&(sensor->data_mutex));
|
|
|
|
return ret;
|
|
}
|
|
|
|
static struct sensor_operate gsensor_icm4260x_ops = {
|
|
.name = "icm4260x_acc",
|
|
.type = SENSOR_TYPE_ACCEL,
|
|
.id_i2c = ACCEL_ID_ICM4260X,
|
|
.read_reg = ICM4260X_ACCEL_DATA_X0,
|
|
.read_len = 6,
|
|
.id_reg = SENSOR_UNKNOW_DATA,
|
|
.id_data = SENSOR_UNKNOW_DATA,
|
|
.precision = ICM4260X_PRECISION,
|
|
.ctrl_reg = ICM4260X_PWR_MGMT_0,
|
|
.int_status_reg = ICM4260X_INT_STATUS,
|
|
.range = {-32768, 32768},
|
|
.trig = IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
|
|
.active = sensor_active,
|
|
.init = sensor_init,
|
|
.report = sensor_report_value,
|
|
};
|
|
|
|
/****************operate according to sensor chip:end************/
|
|
static int gsensor_icm4260x_probe(struct i2c_client *client,
|
|
const struct i2c_device_id *devid)
|
|
{
|
|
client->addr = ICM42607_ADDR;
|
|
return sensor_register_device(client, NULL, devid, &gsensor_icm4260x_ops);
|
|
}
|
|
|
|
static void gsensor_icm4260x_remove(struct i2c_client *client)
|
|
{
|
|
sensor_unregister_device(client, NULL, &gsensor_icm4260x_ops);
|
|
}
|
|
|
|
static const struct i2c_device_id gsensor_icm4260x_id[] = {
|
|
{"icm42607_acc", ACCEL_ID_ICM4260X},
|
|
{}
|
|
};
|
|
|
|
static struct i2c_driver gsensor_icm4260x_driver = {
|
|
.probe = gsensor_icm4260x_probe,
|
|
.remove = (void *)gsensor_icm4260x_remove,
|
|
.shutdown = sensor_shutdown,
|
|
.id_table = gsensor_icm4260x_id,
|
|
.driver = {
|
|
.name = "gsensor_icm4260x",
|
|
#ifdef CONFIG_PM
|
|
.pm = &sensor_pm_ops,
|
|
#endif
|
|
},
|
|
};
|
|
|
|
module_i2c_driver(gsensor_icm4260x_driver);
|
|
|
|
MODULE_AUTHOR("Wangqiang Guo <dave.wang@rock-chips.com>");
|
|
MODULE_DESCRIPTION("icm4260x_acc 3-Axis accelerometer driver");
|
|
MODULE_LICENSE("GPL");
|
|
|