75 lines
2.8 KiB
Plaintext
75 lines
2.8 KiB
Plaintext
ROCKCHIP USB2.0 PHY WITH NANENG IP BLOCK
|
|
|
|
Required properties (phy (parent) node):
|
|
- compatible : should be one of the listed compatibles:
|
|
* "rockchip,rv1126-usb2phy"
|
|
- reg : the address offset of grf for usb-phy configuration.
|
|
- rockchip,grf : phandle to the syscon managing the "general register files"
|
|
- clocks : phandle + phy specifier pair, for the input clocks of phy.
|
|
- clock-names : input clocks name of phy.
|
|
- resets : phandle + reset specifier pairs.
|
|
- reset-names : reset names of phy.
|
|
- #clock-cells : should be 0.
|
|
- clock-output-names : specify the 480m output clock name.
|
|
|
|
Optional properties:
|
|
- assigned-clocks : phandle of usb 480m clock.
|
|
- assigned-clock-parents : parent of usb 480m clock, select between
|
|
usb-phy output 480m and xin24m.
|
|
Refer to clk/clock-bindings.txt for generic clock
|
|
consumer properties.
|
|
- vbus-supply : regulator phandle for vbus power source.
|
|
- wakeup-source : enable bvalid irq and linestate wakeup when suspend.
|
|
only work when suspend wakeup-config is not work.
|
|
- vup-gpios : gpio phandle for pull-up resistor on DM. this property
|
|
is specially provided to RV1126/RV1109 in order to
|
|
increase the amplitude of chirpK and successfully
|
|
complete high speed handshake.
|
|
|
|
Required nodes : a sub-node is required for each port the phy provides.
|
|
The sub-node name is used to identify host or otg port,
|
|
and shall be the following entries:
|
|
* "otg-port" : the name of otg port.
|
|
* "host-port" : the name of host port.
|
|
|
|
Required properties (port (child) node):
|
|
- #phy-cells : must be 0. See ./phy-bindings.txt for details.
|
|
- interrupts : specify an interrupt for each entry in interrupt-names.
|
|
- interrupt-names : a list which should be one of the following cases:
|
|
Regular case:
|
|
* "otg-id" : for the otg id interrupt.
|
|
* "otg-bvalid" : for the otg vbus interrupt.
|
|
* "linestate" : for the host/otg linestate interrupt.
|
|
* "disconnect" : for the host/otg disconnect interrupt.
|
|
|
|
Optional properties:
|
|
- phy-supply : phandle to a regulator that provides power to VBUS.
|
|
See ./phy-bindings.txt for details.
|
|
- rockchip,vbus-always-on: when set, indicates that the otg vbus
|
|
is always powered on.
|
|
|
|
Example:
|
|
|
|
u2phy1: usb2-phy@ff4c8000 {
|
|
compatible = "rockchip,rv1126-usb2phy";
|
|
reg = <0xff4c8000 0x8000>;
|
|
rockchip,grf = <&grf>;
|
|
clocks = <&pmucru CLK_USBPHY_HOST_REF>, <&cru PCLK_USBPHY_HOST>;
|
|
clock-names = "phyclk", "pclk";
|
|
assigned-clocks = <&cru USB480M>;
|
|
assigned-clock-parents = <&u2phy1>;
|
|
resets = <&cru SRST_USBPHYPOR_HOST>, <&cru SRST_USBPHY_HOST_P>;
|
|
reset-names = "u2phy", "u2phy-apb";
|
|
#clock-cells = <0>;
|
|
clock-output-names = "usb480m_phy";
|
|
status = "disabled";
|
|
|
|
u2phy_host: host-port {
|
|
#phy-cells = <0>;
|
|
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "linestate", "disconnect";
|
|
status = "disabled";
|
|
};
|
|
};
|