218 lines
5.9 KiB
Plaintext
218 lines
5.9 KiB
Plaintext
Imagination Technologies Pistachio SoC pin controllers
|
|
======================================================
|
|
|
|
The pin controllers on Pistachio are a combined GPIO controller, (GPIO)
|
|
interrupt controller, and pinmux + pinconf device. The system ("east") pin
|
|
controller on Pistachio has 99 pins, 90 of which are MFIOs which can be
|
|
configured as GPIOs. The 90 GPIOs are divided into 6 banks of up to 16 GPIOs
|
|
each. The GPIO banks are represented as sub-nodes of the pad controller node.
|
|
|
|
Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
|
|
../interrupt-controller/interrupts.txt for generic information regarding
|
|
pin controller, GPIO, and interrupt bindings.
|
|
|
|
Required properties for pin controller node:
|
|
--------------------------------------------
|
|
- compatible: "img,pistachio-system-pinctrl".
|
|
- reg: Address range of the pinctrl registers.
|
|
|
|
Required properties for GPIO bank sub-nodes:
|
|
--------------------------------------------
|
|
- interrupts: Interrupt line for the GPIO bank.
|
|
- gpio-controller: Indicates the device is a GPIO controller.
|
|
- #gpio-cells: Must be two. The first cell is the GPIO pin number and the
|
|
second cell indicates the polarity. See <dt-bindings/gpio/gpio.h> for
|
|
a list of possible values.
|
|
- interrupt-controller: Indicates the device is an interrupt controller.
|
|
- #interrupt-cells: Must be two. The first cell is the GPIO pin number and
|
|
the second cell encodes the interrupt flags. See
|
|
<dt-bindings/interrupt-controller/irq.h> for a list of valid flags.
|
|
|
|
Note that the N GPIO bank sub-nodes *must* be named gpio0, gpio1, ... gpioN-1.
|
|
|
|
Required properties for pin configuration sub-nodes:
|
|
----------------------------------------------------
|
|
- pins: List of pins to which the configuration applies. See below for a
|
|
list of possible pins.
|
|
|
|
Optional properties for pin configuration sub-nodes:
|
|
----------------------------------------------------
|
|
- function: Mux function for the specified pins. This is not applicable for
|
|
non-MFIO pins. See below for a list of valid functions for each pin.
|
|
- bias-high-impedance: Enable high-impedance mode.
|
|
- bias-pull-up: Enable weak pull-up.
|
|
- bias-pull-down: Enable weak pull-down.
|
|
- bias-bus-hold: Enable bus-keeper mode.
|
|
- drive-strength: Drive strength in mA. Supported values: 2, 4, 8, 12.
|
|
- input-schmitt-enable: Enable Schmitt trigger.
|
|
- input-schmitt-disable: Disable Schmitt trigger.
|
|
- slew-rate: Slew rate control. 0 for slow, 1 for fast.
|
|
|
|
Pin Functions
|
|
--- ---------
|
|
mfio0 spim1
|
|
mfio1 spim1, spim0, uart1
|
|
mfio2 spim1, spim0, uart1
|
|
mfio3 spim1
|
|
mfio4 spim1
|
|
mfio5 spim1
|
|
mfio6 spim1
|
|
mfio7 spim1
|
|
mfio8 spim0
|
|
mfio9 spim0
|
|
mfio10 spim0
|
|
mfio11 spis
|
|
mfio12 spis
|
|
mfio13 spis
|
|
mfio14 spis
|
|
mfio15 sdhost, mips_trace_clk, mips_trace_data
|
|
mfio16 sdhost, mips_trace_dint, mips_trace_data
|
|
mfio17 sdhost, mips_trace_trigout, mips_trace_data
|
|
mfio18 sdhost, mips_trace_trigin, mips_trace_data
|
|
mfio19 sdhost, mips_trace_dm, mips_trace_data
|
|
mfio20 sdhost, mips_trace_probe_n, mips_trace_data
|
|
mfio21 sdhost, mips_trace_data
|
|
mfio22 sdhost, mips_trace_data
|
|
mfio23 sdhost
|
|
mfio24 sdhost
|
|
mfio25 sdhost
|
|
mfio26 sdhost
|
|
mfio27 sdhost
|
|
mfio28 i2c0, spim0
|
|
mfio29 i2c0, spim0
|
|
mfio30 i2c1, spim0
|
|
mfio31 i2c1, spim1
|
|
mfio32 i2c2
|
|
mfio33 i2c2
|
|
mfio34 i2c3
|
|
mfio35 i2c3
|
|
mfio36 i2s_out, audio_clk_in
|
|
mfio37 i2s_out, debug_raw_cca_ind
|
|
mfio38 i2s_out, debug_ed_sec20_cca_ind
|
|
mfio39 i2s_out, debug_ed_sec40_cca_ind
|
|
mfio40 i2s_out, debug_agc_done_0
|
|
mfio41 i2s_out, debug_agc_done_1
|
|
mfio42 i2s_out, debug_ed_cca_ind
|
|
mfio43 i2s_out, debug_s2l_done
|
|
mfio44 i2s_out
|
|
mfio45 i2s_dac_clk, audio_sync
|
|
mfio46 audio_trigger
|
|
mfio47 i2s_in
|
|
mfio48 i2s_in
|
|
mfio49 i2s_in
|
|
mfio50 i2s_in
|
|
mfio51 i2s_in
|
|
mfio52 i2s_in
|
|
mfio53 i2s_in
|
|
mfio54 i2s_in, spdif_in
|
|
mfio55 uart0, spim0, spim1
|
|
mfio56 uart0, spim0, spim1
|
|
mfio57 uart0, spim0, spim1
|
|
mfio58 uart0, spim1
|
|
mfio59 uart1
|
|
mfio60 uart1
|
|
mfio61 spdif_out
|
|
mfio62 spdif_in
|
|
mfio63 eth, mips_trace_clk, mips_trace_data
|
|
mfio64 eth, mips_trace_dint, mips_trace_data
|
|
mfio65 eth, mips_trace_trigout, mips_trace_data
|
|
mfio66 eth, mips_trace_trigin, mips_trace_data
|
|
mfio67 eth, mips_trace_dm, mips_trace_data
|
|
mfio68 eth, mips_trace_probe_n, mips_trace_data
|
|
mfio69 eth, mips_trace_data
|
|
mfio70 eth, mips_trace_data
|
|
mfio71 eth
|
|
mfio72 ir
|
|
mfio73 pwmpdm, mips_trace_clk, sram_debug
|
|
mfio74 pwmpdm, mips_trace_dint, sram_debug
|
|
mfio75 pwmpdm, mips_trace_trigout, rom_debug
|
|
mfio76 pwmpdm, mips_trace_trigin, rom_debug
|
|
mfio77 mdc_debug, mips_trace_dm, rpu_debug
|
|
mfio78 mdc_debug, mips_trace_probe_n, rpu_debug
|
|
mfio79 ddr_debug, mips_trace_data, mips_debug
|
|
mfio80 ddr_debug, mips_trace_data, mips_debug
|
|
mfio81 dreq0, mips_trace_data, eth_debug
|
|
mfio82 dreq1, mips_trace_data, eth_debug
|
|
mfio83 mips_pll_lock, mips_trace_data, usb_debug
|
|
mfio84 audio_pll_lock, mips_trace_data, usb_debug
|
|
mfio85 rpu_v_pll_lock, mips_trace_data, sdhost_debug
|
|
mfio86 rpu_l_pll_lock, mips_trace_data, sdhost_debug
|
|
mfio87 sys_pll_lock, dreq2, socif_debug
|
|
mfio88 wifi_pll_lock, dreq3, socif_debug
|
|
mfio89 bt_pll_lock, dreq4, dreq5
|
|
tck
|
|
trstn
|
|
tdi
|
|
tms
|
|
tdo
|
|
jtag_comply
|
|
safe_mode
|
|
por_disable
|
|
resetn
|
|
|
|
Example:
|
|
--------
|
|
pinctrl@18101c00 {
|
|
compatible = "img,pistachio-system-pinctrl";
|
|
reg = <0x18101C00 0x400>;
|
|
|
|
gpio0: gpio0 {
|
|
interrupts = <GIC_SHARED 71 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
...
|
|
|
|
gpio5: gpio5 {
|
|
interrupts = <GIC_SHARED 76 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
...
|
|
|
|
uart0_xfer: uart0-xfer {
|
|
uart0-rxd {
|
|
pins = "mfio55";
|
|
function = "uart0";
|
|
};
|
|
uart0-txd {
|
|
pins = "mfio56";
|
|
function = "uart0";
|
|
};
|
|
};
|
|
|
|
uart0_rts_cts: uart0-rts-cts {
|
|
uart0-rts {
|
|
pins = "mfio57";
|
|
function = "uart0";
|
|
};
|
|
uart0-cts {
|
|
pins = "mfio58";
|
|
function = "uart0";
|
|
};
|
|
};
|
|
};
|
|
|
|
uart@... {
|
|
...
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_xfer>, <&uart0_rts_cts>;
|
|
...
|
|
};
|
|
|
|
usb_vbus: fixed-regulator {
|
|
...
|
|
gpio = <&gpio5 6 GPIO_ACTIVE_HIGH>;
|
|
...
|
|
};
|