// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (c) 2020 Rockchip Electronics Co., Ltd. * */ #include "rk3568-evb-rk628-ddr4-v10.dtsi" #include "rk3568-android.dtsi" / { panel@0 { compatible = "simple-panel"; disp_timings3: display-timings { native-mode = <&rgb2lvds_timing>; rgb2lvds_timing: timing0 { clock-frequency = <148500000>; hactive = <1920>; vactive = <1080>; hback-porch = <148>; hfront-porch = <88>; vback-porch = <36>; vfront-porch = <4>; hsync-len = <44>; vsync-len = <5>; hsync-active = <0>; vsync-active = <0>; de-active = <0>; pixelclk-active = <0>; }; }; port { panel_in_rgb: endpoint { remote-endpoint = <&rgb_out_panel>; }; }; }; }; &backlight { enable-gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>; }; >1x { status = "disabled"; }; &i2c2_rk628 { panel-backlight = <&backlight>; panel-power-supply = <&vcc3v3_lcd0_n>; panel-reset-delay-ms = <10>; panel-enable-delay-ms = <100>; panel-prepare-delay-ms = <60>; panel-unprepare-delay-ms = <10>; panel-disable-delay-ms = <60>; pinctrl-names = "default"; pinctrl-0 = <&rk628_reset &refclk_pins>; assigned-clocks = <&pmucru CLK_WIFI>; assigned-clock-rates = <24000000>; clocks = <&pmucru CLK_WIFI>; clock-names = "soc_24M"; rk628-rgb-in; rk628-gvi-out { /* "rgb666" * "rgb888" * "rgb101010" * "yuyv8" * "yuyv10" */ bus-format = "rgb888"; gvi,lanes = <8>; //"rockchip,division-mode"; //"rockchip, gvi-frm-rst"; status = "okay"; }; display-timings { src-timing { clock-frequency = <148500000>; hactive = <1920>; vactive = <1080>; hback-porch = <148>; hfront-porch = <88>; vback-porch = <36>; vfront-porch = <4>; hsync-len = <44>; vsync-len = <5>; hsync-active = <0>; vsync-active = <0>; de-active = <0>; pixelclk-active = <0>; }; dst-timing { clock-frequency = <594000000>; hactive = <3840>; vactive = <2160>; hback-porch = <296>; hfront-porch = <176>; vback-porch = <72>; vfront-porch = <8>; hsync-len = <88>; vsync-len = <10>; hsync-active = <0>; vsync-active = <0>; de-active = <0>; pixelclk-active = <0>; }; }; }; &route_rgb { status = "okay"; bridge = <&i2c2_rk628>; }; &rgb_in_vp2 { status = "okay"; }; &rgb { status = "okay"; ports { port@1 { reg = <1>; rgb_out_panel: endpoint { remote-endpoint = <&panel_in_rgb>; }; }; }; }; &vcc3v3_lcd0_n { gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>; enable-active-high; };